Tugas Administrasi Jaringan KONFIGURASI Inter-VLAN Routing

Tugas :

Buatlah skema jaringan dibawah berikut dengan ketentuan di bawah ini :

1.Ikuti skema jaringan di atas beserta IP nya
2.Gunakanlah nomor absen anda untuk mengisi vlan keduanya contoh diatas adalah vlan 30 sedangkan nomor absen saya 8 jadi saya akan menggunakan vlan 8 sebagai vlan kedua.

Berikut adalah step by step pengerjaan tugas nya :

1.Sediakan perangkat sesuai skema
2.Pasang kabel sesuai skema
3.Konfigurasi Router
4.Konfigurasi Switch
5.Jika sudah selesai lalu uji koneksi nya



              Konfigurasi Router

Router>enable

Router#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#interface g0/0.10

Router(config-subif)#encapsulation dot1q 10

Router(config-subif)#ip address 172.17.10.1 255.255.255.0

Router(config-subif)#exit

Router(config)#interface g0/1.8

Router(config-subif)#encapsulation dot1q 8

Router(config-subif)#ip address 172.17.8.1 255.255.255.0

Router(config-subif)#exit

Router(config)#interface g0/0

Router(config-if)#no shutdown

Router(config-if)#

%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

%LINK-5-CHANGED: Interface GigabitEthernet0/0.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.10, changed state to up

Router(config-if)#interface g0/1

Router(config-if)#no shutdown

Router(config-if)#

%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up

%LINK-5-CHANGED: Interface GigabitEthernet0/1.8, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1.8, changed state to up

Router(config-if)#exit

Router(config)#

Router(config)#exit

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router#copy running-config startup-config

Destination filename [startup-config]?

Building configuration...

[OK]

Router#

             Konfigurasi Switch

Switch>enable

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Switch(config)#vlan 10

Switch(config-vlan)#name vlan10

Switch(config-vlan)#vlan 8

Switch(config-vlan)#name vlan8

Switch(config-vlan)#exit

Switch(config)#interface g0/1

Switch(config-if)#switchport mode trunk

Switch(config-if)#exit

Switch(config)#interface g0/2

Switch(config-if)#switchport mode trunk

Switch(config-if)#exit

Switch(config)#interface fastEthernet 0/1

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 10

Switch(config-if)#exit

Switch(config)#interface fastEthernet 0/2

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 8

Switch(config-if)#exit

Switch(config)#exit

Switch#

%SYS-5-CONFIG_I: Configured from console by console

Switch#copy running-config startup-config

Destination filename [startup-config]?

Building configuration...

[OK]

Switch#

                        IP PC VLAN 10

                        IP VLAN 8

                       Skema yang sudah jadi

                           Uji koneksi